# Pipestra Flange – method, data sources and limits Pipestra Flange is a browser tool with three parts: flange pressure–temperature rating, bolt tightening torque, and a simplified gasket check. It is our own implementation of published methods. All calculations run in your browser and your inputs stay on your device. **A qualified engineer must check every result before it is used. This is not a full EN 1591-1 or ASME VIII-1 Appendix 2 flange design.** ## 1 Pressure–temperature rating ### EN 1092-1 (steel flanges, PN designated) - Data: EN 1092-1:2018 Annex G (PN 6, 10, 16, 25, 40, 63, 100). Flange dimensions (D, K, bolt holes, number of bolts, bolt size) come from Tables 11–17, DN 10–600 (PN 63 up to DN 400, PN 100 up to DN 350). Raised-face d1 comes from Table 8. - Material groups: 3E0 and 3E1 (non-alloy steel, two thickness rows "a"/"b"), 10E0 (1.4307), 11E0 (1.4301), 12E0 (1.4541), 13E0 (1.4404), 14E0 (1.4401), 15E0 (1.4571) and 16E0 (1.4462, up to 250 °C). - Temperature range: −10 °C up to 400 °C for 3E0/3E1 and up to 500 °C for the austenitic groups. The tool warns above that, because the higher table values are creep-governed. - Interpolation: the room-temperature (RT) value applies from −10 to 50 °C. Above 50 °C the tool interpolates linearly between 20 °C (taken as the RT value) and 100 °C, which gives a slightly conservative result. Above 100 °C it interpolates between the table temperatures. The result is rounded down to 0.1 bar. - Cross-checks: the values were checked against a second public reproduction of the EN 1092-1 tables (3E0 rows). ### ASME B16.5 (Class 150–2500) - Two editions are included, and you can choose either one: - **2017/2020** (default). Values were checked against three independent public reproductions. - **2025**, where some values changed slightly. Values were checked against two agreeing public reproductions. - Material groups: 1.1 (carbon steel, e.g. A105), 2.1 (304/304H), 2.2 (316/316H) and 2.3 (304L/316L). The data covers −29 °C up to 538 °C (2.3 ends at 450 °C in 2017/2020 and at 454 °C in 2025). Other groups are not included yet. - Interpolation: the first row applies up to 38 °C; above that, linear interpolation between table temperatures. The result is rounded down to 0.1 bar. - Dimensions: NPS ½–24 for all six classes. These are our own table and agree with a public reproduction on every row. Bolt holes are the bolt diameter + 1/8 in. The rating is a PASS when the design pressure is at or below the interpolated rating at the design temperature. Pipe loads (bending moments and axial forces) are **not** included, and the tool warns about this. ## 2 Bolt tightening torque **Thread geometry** - Metric coarse threads (ISO 261/724), M10–M64: d2 = d − 0.649519·P, d3 = d − 1.226869·P, stress area As = π/4·((d2+d3)/2)², root area Ar = π/4·d3². - UNC / 8UN inch threads, ½–3½ in (8UN from 1 in): As = π/4·(d − 0.974279·P)², Ar = π/4·(d − 1.299038·P)². - Nut bearing diameter: dw is taken from typical metric hex-nut dimensions (width across flats), and dw = 0.95·(1.5·d + 1/8 in) for inch heavy-hex nuts. You can override dw. Dh is the bolt hole diameter. **Bolt materials (min. yield Rp0.2 / tensile Rm)** - Metric: 5.6, 8.8, 10.9, 12.9 (ISO 898-1); A2-70, A4-70, A4-80 (ISO 3506-1). - ASTM: A193 B7, B7M, B16, B8 Class 1, B8M Class 1 and Class 2; A320 L7. These include the size-dependent yield values for the larger diameters. **Preload** (F) - Set it as a percentage of yield, as a target bolt stress, or as a force. - It is taken on the stress area or on the root area (the root area is the usual reference for ASME bolting). **Tightening torque** (full formula, VDI 2230 style) - M_A = F·(0.16·P + 0.58·d2·µG + µK·DKm/2), with DKm = (dw + Dh)/2. - Friction presets: dry 0.20, oil 0.15, nickel paste 0.14, copper paste 0.12, MoS2 0.10, PTFE-coated 0.08. These are typical values only; use your lubricant supplier's data where you have it. - The tool also shows the equivalent nut factor K_eq = M_A/(F·d). **Nut factor method:** T = K·F·d. Typical K: 0.20 (dry, as-received), 0.16–0.18 (oiled) and 0.12–0.14 (good anti-seize). The tool shows both results, and you choose which one goes into the table and the passes. **Tightening stress check** - σred = √(σM² + 3·τ²), with σM = F/As and τ = M_G/(π·ds³/16), where M_G = F·(0.16·P + 0.58·d2·µG) and ds = (d2+d3)/2. - The tool warns if the utilisation σred/Rp0.2 is above 0.9. **Tightening sequence** - Bolts are tightened in opposite pairs. Each next pair is the one furthest from the pairs already tightened, so the load spreads evenly round the flange. - Passes: 30 %, 60 % and 100 % of the final torque in the cross pattern, then a check pass at 100 % going round the circle until no nut turns any more. - This is a common, general practice, described here in our own words. For critical joints, follow your company procedure and a recognised guideline (for example ASME PCC-1). ## 3 Simplified gasket check (ASME VIII-1 Appendix 2 style) - Basic gasket seating width: N = (OD − ID)/2 and b0 = N/2. The effective width is b = b0 when b0 ≤ 6.35 mm; otherwise b = 0.5·√(b0/25.4)·25.4 mm. The gasket reaction diameter G is the mean diameter for narrow gaskets and OD − 2b for wide ones. - Loads: H = π/4·G²·P, Hp = 2·b·π·G·m·P, Wm1 = H + Hp (operating) and Wm2 = π·b·G·y (seating). - Bolt area: Am = max(Wm1/Sb, Wm2/Sa) is compared with the available area Ab = n·Ar. Sb and Sa are the allowable bolt stresses: 25 ksi (172 MPa) for B7/L7/B16, otherwise min(Rp0.2/3, Rm/4) as a simple preset. You can override them. - Assembly: W_A = n·F is checked against Wm1. The gasket stress σg = W_A / (π/4·(OD² − ID²)) is checked against the seating stress y and a typical maximum gasket stress. - m and y presets follow the commonly published Table 2-5.1 values. The maximum stresses are typical values only; use the gasket manufacturer's data. - This check is **not** EN 1591-1. It does not cover flange stresses or rotation, bolt-load scatter, creep relaxation, thermal effects, or tightness classes. ## 4 Reports and files - PDF report: your browser's print to PDF. It holds the inputs, results, step-by-step working, warnings, the torque table, the tightening passes and the disclaimer. - CSV export, and save/open of a `.pflange.json` project file. - Language: English and German. ## 5 Out of scope / warnings The tool warns in these cases: - the temperature is outside the table range; - the pressure is above the rating; - the bolt material temperature limit is exceeded; - the bolt utilisation is above 90 %; - the gasket stress is below y or above the maximum; - the gasket temperature limit is exceeded. It also always reminds you that external pipe loads are not included and that a qualified engineer has to review the results.